Images shown are for reference only. Product specifications, packaging, and appearance may differ based on brand or batch.
123.00 USD
Yaseen Construction Products supplies Bitumen 60/70, a penetration-grade paving bitumen used in asphalt road construction, highway development, pavement rehabilitation and infrastructure projects.
Bitumen 60/70 is classified by its needle penetration range of 60–70 dmm at 25°C under specified testing conditions. It is commonly used as a binder in approved hot-mix asphalt formulations, including asphalt concrete, binder courses and wearing courses.
Bitumen 60/70 is a petroleum-derived paving binder commonly used in the production of hot-mix asphalt for road construction and pavement maintenance.
The designation 60/70 refers to its penetration range at a specified temperature, load and testing duration. This classification helps engineers and asphalt manufacturers select a binder with the required consistency for a particular pavement application.
Bitumen 60/70 is used in approved asphalt mixtures for highways, urban roads, industrial access roads, commercial developments and other infrastructure projects.
Yaseen Construction Products sources penetration-grade Bitumen 60/70 for asphalt mixing plants, road contractors, civil engineering companies, infrastructure developers and international procurement teams.
Bitumen 60/70 is a penetration-grade paving bitumen.
Its principal classification is based on a standard needle penetration test.
Under the conventional test conditions of 25°C, a 100 g load and five seconds, the penetration range is 60–70 units of 0.1 mm.
This corresponds to a penetration depth of 6.0–7.0 mm under the test conditions.
The penetration grade does not directly state the binder’s softening point, viscosity, service temperature or suitability for every climate.
Those properties require separate testing.
Bitumen acts as the binder in an asphalt mixture.
It coats the mineral aggregates and helps form a cohesive pavement material after mixing, laying and compaction.
Its performance depends on:
Aggregate grading.
Binder content.
Mixture design.
Binder properties.
Mixing temperature.
Compaction.
Traffic loading.
Pavement structure.
Climate.
Drainage.
Bitumen 60/70 is one component of the asphalt mixture. The completed pavement’s performance depends on the entire design and construction process.
Paving bitumen is produced through petroleum refining and, where applicable, controlled blending or further processing.
The production process depends on the refinery and the required specification.
A typical supply process includes:
Selecting suitable refinery feedstock.
Processing the material through refinery operations.
Controlling binder properties.
Testing penetration and other required characteristics.
Verifying compliance with the applicable grade specification.
Storing the approved binder.
Loading it into suitable bulk transport or export packaging.
Each supplied batch should be supported by the required quality documentation.
| Parameter | Specification / Selection Criteria |
|---|---|
| Product | Bitumen 60/70 |
| Material Type | Penetration-Grade Paving Bitumen |
| Penetration at 25°C | 60–70 dmm |
| Penetration Test Conditions | 100 g, 5 Seconds |
| Appearance | Black to Dark Brown |
| Softening Point | As Required by Applicable Specification |
| Ductility | As Required by Applicable Specification |
| Flash Point | As Required by Applicable Specification |
| Solubility | As Required by Applicable Specification |
| Specific Gravity / Density | Manufacturer Declared |
| Kinematic Viscosity | Where Required |
| Dynamic Viscosity | Where Required |
| Loss on Heating | Where Required |
| Retained Penetration After Ageing | Where Required |
| Softening Point Increase After Ageing | Where Required |
| Rolling Thin Film Oven Test | Where Required |
| Storage Temperature | Manufacturer Specified |
| Mixing Temperature | Asphalt Mix Design Dependent |
| Packaging | Bulk Tanker, Steel Drums, Bitutainers or Approved Containers |
The penetration range identifies the grade. Other acceptance limits depend on the governing specification, which may include ASTM, AASHTO, national road authority or project-specific requirements.
Bitumen 60/70 and 80/100 are different penetration grades.
| Property | Bitumen 60/70 | Bitumen 80/100 |
|---|---|---|
| Penetration at 25°C | 60–70 dmm | 80–100 dmm |
| Relative Consistency | Harder | Softer |
| Classification | Penetration Grade | Penetration Grade |
| Asphalt Use | Mix Design Dependent | Mix Design Dependent |
| Climate Suitability | Requires Engineering Assessment | Requires Engineering Assessment |
| Substitution | Requires Approval | Requires Approval |
A harder binder is not automatically better for every road.
The selection must consider rutting resistance, cracking resistance, traffic and pavement temperature.
Bitumen 40/50 has a lower penetration range and is generally harder than Bitumen 60/70.
The correct grade depends on the pavement design and the applicable road specification.
VG30 is a viscosity-grade bitumen classification.
Bitumen 60/70 is a penetration-grade classification.
Although the two grades may sometimes be compared in procurement discussions, they are not automatically interchangeable.
| Property | Bitumen 60/70 | VG30 |
|---|---|---|
| Classification | Penetration Grade | Viscosity Grade |
| Primary Grading Basis | Needle Penetration | Viscosity |
| Governing Specification | Project Dependent | Project Dependent |
| Direct Equivalence | Not Assumed | Not Assumed |
| Selection | Approved Mix Design | Approved Mix Design |
Any proposed substitution requires review of the full binder specification.
Bitumen 60/70 and MC 70 are different products.
| Property | Bitumen 60/70 | MC 70 |
|---|---|---|
| Product Type | Paving Bitumen | Medium-Curing Cutback Asphalt |
| Grade Basis | Penetration | Viscosity |
| Added Petroleum Solvent | Not Normally | Yes |
| Main Application | Asphalt Mix Binder | Approved Granular Base Priming |
| Typical Handling | Heated Binder | Cutback Asphalt Handling |
| Main Function | Aggregate Binding | Surface Penetration and Priming |
The number 70 has a different meaning in each designation.
Oxidised bitumen is processed through controlled air blowing to achieve particular industrial properties.
Bitumen 60/70 is a paving bitumen grade.
Oxidised bitumen is commonly used in selected roofing, waterproofing and industrial compounds, while Bitumen 60/70 is primarily used in approved asphalt mixtures.
Polymer modified bitumen contains approved polymers designed to change specified binder properties.
Bitumen 60/70 is a conventional penetration-grade binder.
Polymer modification may be required for particular pavement temperatures, traffic loads or performance requirements.
The two materials should not be substituted without engineering approval.
Bitumen 60/70 may be used in approved highway asphalt mixtures.
The pavement design must consider:
Traffic volume.
Heavy vehicle loading.
Pavement temperature.
Aggregate properties.
Binder content.
Asphalt mixture type.
Compaction requirements.
Drainage.
Expected service life.
The road authority determines the acceptable binder grade.
Bitumen 60/70 is used in suitable asphalt mixtures for urban road construction and rehabilitation.
Urban pavements may experience:
Frequent braking.
Turning movements.
Bus and truck traffic.
Utility reinstatements.
Variable drainage conditions.
The asphalt mix design must account for these conditions.
Industrial roads and logistics areas may carry frequent heavy vehicle traffic.
Bitumen 60/70 may be suitable where the pavement design and binder specification approve it.
High loading and slow-moving vehicles may require additional mixture performance testing or a different binder grade.
Wearing courses form the upper asphalt layer exposed to traffic and weather.
Bitumen 60/70 may be used in approved wearing-course mixtures.
Performance depends on aggregate selection, binder content, compaction, surface texture and pavement conditions.
Binder courses provide an intermediate structural layer in many flexible pavement designs.
Bitumen 60/70 may be specified as the binder in suitable asphalt mixtures.
The required binder content and mixture properties must be established through an approved mix design.
Selected asphalt base mixtures may use Bitumen 60/70.
The material must meet the pavement design and applicable construction specifications.
Airport asphalt pavements are subject to specialised loading and operational requirements.
Bitumen 60/70 should be used only where the relevant airport pavement specification approves it.
Airport projects may require performance-graded or modified binders.
Bitumen 60/70 may be used in new asphalt mixtures placed during road rehabilitation.
Applications may include:
Asphalt overlays.
Pavement reconstruction.
Localised repairs.
Road widening.
Asphalt reinstatement.
The selected binder must meet the approved mix design.
Asphalt mixing plants use paving bitumen to produce asphalt mixtures.
Important procurement considerations include:
Binder grade.
Delivery temperature.
Storage temperature.
Tank capacity.
Mixing plant requirements.
Quantity.
Delivery frequency.
Batch quality documentation.
The asphalt mixture must be designed using the approved project method.
Common design considerations include:
Aggregate grading.
Binder content.
Air voids.
Voids in mineral aggregate.
Moisture susceptibility.
Stability or performance testing.
Rutting resistance.
Cracking resistance.
Compaction characteristics.
Bitumen grade alone does not establish asphalt mixture quality.
Bitumen 60/70 is normally handled in heated condition for asphalt production.
The correct temperature depends on the product’s viscosity, storage system and asphalt mix design.
Important handling requirements include:
Use approved heating equipment.
Monitor material temperature.
Avoid overheating.
Prevent water contamination.
Maintain safe tank levels.
Use suitable insulated equipment.
Follow the safety data sheet.
Prevent contact with hot bitumen.
Hot bitumen can cause severe burns.
Water entering hot bitumen may cause violent foaming or overflow.
Bitumen 60/70 should be stored according to the manufacturer’s instructions.
Storage considerations include:
Suitable heated tanks.
Temperature monitoring.
Insulation.
Contamination prevention.
Safe loading and unloading.
Tank maintenance.
Fire safety.
Appropriate ventilation.
Prolonged excessive heating can alter binder properties.
The supplied binder may fall outside the required penetration range.
Batch testing should confirm compliance.
Overheating may accelerate ageing and alter binder properties.
Water can cause foaming and safety hazards during heating.
Variation between deliveries may affect asphalt production.
A penetration-grade binder may be unsuitable for certain traffic or climate conditions.
Pavement distress can result from mixture design, aggregate quality, compaction, drainage or construction defects, even when the binder meets its specification.
| Standard | Application |
|---|---|
| ASTM D946/D946M | Penetration-graded asphalt binder for pavement construction |
| ASTM D5/D5M | Penetration of bituminous materials |
| ASTM D36/D36M | Softening point by ring-and-ball apparatus |
| ASTM D113 | Ductility of asphalt materials |
| ASTM D92 | Flash and fire points by Cleveland open cup tester |
| ASTM D2042 | Solubility of asphalt materials |
| ASTM D2170/D2170M | Kinematic viscosity of asphalt |
| ASTM D2171/D2171M | Viscosity of asphalt by vacuum capillary viscometer |
| ASTM D2872 | Effect of heat and air on a moving film of asphalt binder |
| EN 12591 | Specifications for paving grade bitumens, where adopted |
The applicable standard and edition must be confirmed for each project.
EN 12591 uses its own grading and acceptance requirements. A nominally similar penetration range does not establish full equivalence between specifications.
Buyers should confirm:
Penetration grade.
Applicable standard.
Softening point.
Ductility.
Flash point.
Solubility.
Viscosity.
Ageing requirements.
Asphalt mixture type.
Road authority approval.
Storage and delivery requirements.
Packaging.
Order quantity.
Bitumen 60/70 may be supplied in:
Bulk heated tankers.
Steel drums.
Bitutainers.
Other approved export packaging.
Packaging depends on manufacturer availability, order quantity, transport conditions and destination.
Bitumen quantity is generally calculated from the approved asphalt mix design.
Bitumen requirement (tonnes) = Asphalt mixture quantity (tonnes) × Binder percentage by total mixture mass ÷ 100
For example, assume:
Asphalt mixture quantity: 5,000 tonnes.
Approved binder content: 5.0% by total mixture mass.
Theoretical bitumen requirement:
5,000 × 0.05 = 250 tonnes.
With an illustrative 2% procurement allowance:
255 tonnes.
This is a calculation example only. Actual binder content must come from the approved asphalt mix design.
Pricing depends on:
Refinery source.
Applicable specification.
Order quantity.
Packaging.
Market conditions.
Freight.
Delivery destination.
Delivery schedule.
For procurement comparisons, buyers should confirm whether quotations are based on bulk tanker delivery, drums or other export packaging.
For a specification-based quotation, provide:
Project location.
Required Bitumen 60/70 standard.
Technical specification.
Asphalt plant or project requirements.
Required quantity.
Packaging preference.
Delivery destination.
Delivery schedule.
Required quality documentation.
Yaseen Construction Products supplies and exports Bitumen 60/70 for asphalt road construction, highway development, industrial pavements, road rehabilitation and approved infrastructure projects across the UAE, Saudi Arabia, Qatar, Oman, Kuwait and African countries, including Nigeria, Kenya, Ghana, Tanzania, Uganda, Ethiopia, South Africa, Egypt, Morocco, Rwanda, Zambia, Mozambique and Senegal.
We support asphalt mixing plants, road contractors, highway developers, civil engineering companies and procurement teams with specification-based sourcing, bulk quotations and international shipment arrangements.
Product availability, pricing and delivery schedules depend on grade, specification, packaging, quantity and destination.
Established Penetration Grade: Defined by a penetration range of 60–70 dmm at 25°C.
Asphalt Binder: Used to bind mineral aggregates in approved asphalt mixtures.
Road Construction Applications: Suitable for specified highways, urban roads and access roads.
Asphalt Wearing Courses: Used in approved surface-course mixtures.
Asphalt Binder Courses: Suitable for selected intermediate pavement layers.
Asphalt Base Courses: Can be used in approved structural asphalt mixtures.
Mix Design Compatibility: Can be evaluated through standard asphalt mixture design procedures.
Quality Testing: Penetration, softening point, viscosity and other properties can be verified.
Bulk Asphalt Plant Supply: Suitable for procurement by asphalt mixing plants.
Multiple Packaging Options: Available in bulk and approved export packaging, subject to supplier availability.
Specification-Based Sourcing: Can be sourced against applicable paving bitumen standards.
International Project Supply: Suitable for road construction and infrastructure procurement.
Highway Construction: Binder in approved highway asphalt mixtures.
Urban Roads: Asphalt paving for suitable municipal road projects.
Industrial Roads: Binder for approved industrial access roads.
Asphalt Wearing Courses: Production of specified road surface mixtures.
Asphalt Binder Courses: Binder in approved intermediate asphalt layers.
Asphalt Base Courses: Production of suitable structural asphalt mixtures.
Road Rehabilitation: Asphalt overlays and pavement reconstruction.
Road Widening: New asphalt pavement construction.
Commercial Developments: Asphalt access roads and internal road networks.
Logistics Parks: Asphalt pavement for suitable logistics infrastructure.
Airport Pavements: Use only where the airport pavement specification approves the grade.
Asphalt Mixing Plants: Production of approved hot-mix asphalt materials.
Bitumen 60/70 is a penetration-grade paving bitumen used in approved asphalt mixtures for road construction and infrastructure projects. Its penetration range is 60–70 dmm under specified test conditions.
The numbers indicate a needle penetration range of 60–70 units of 0.1 mm, tested at 25°C under a 100 g load for five seconds.
Bitumen 60/70 is used as a binder in approved asphalt mixtures for highways, urban roads, industrial roads, wearing courses, binder courses and road rehabilitation projects.
Bitumen 60/70 has a lower penetration range and is generally harder than Bitumen 80/100. The correct grade depends on traffic, climate, asphalt mix design and the governing road specification.
Bitumen 60/70 is classified by penetration, while VG30 is classified by viscosity. They are not automatically equivalent, and substitution requires approval against the full technical specification.
Bitumen 60/70 is a paving binder used in asphalt mixtures. MC 70 is a medium-curing cutback asphalt used for approved granular base priming. Their grading systems and applications differ.
Yes, where the highway specification approves the grade. The asphalt mix design must account for traffic loading, climate, aggregate properties and pavement performance.
Suitability depends on pavement temperature, traffic, binder properties and mix design. Some high-temperature or heavily loaded pavements may require different or modified binders.
Absolutely. We provide Bitumen 60/70 at highly competitive, manufacturer-equivalent prices. Please contact us for bulk pricing, delivery options, and availability.
Yes. Bitumen 60/70 may be used in approved wearing-course mixtures where the road authority and asphalt mix design permit it.
Common tests include penetration, softening point, ductility, viscosity, flash point, solubility and ageing performance, depending on the governing specification.
The quantity depends on the approved binder content. For example, a 5,000-tonne asphalt mixture containing 5% binder by total mixture mass requires 250 tonnes of bitumen before procurement allowances.
Yaseen Construction Products supplies and exports Bitumen 60/70 for asphalt roads, highways, industrial pavements and infrastructure projects across the UAE, Saudi Arabia, Qatar, Oman, Kuwait and African countries, including Nigeria, Kenya, Ghana, Tanzania, Uganda, Ethiopia, South Africa, Egypt, Morocco, Rwanda, Zambia, Mozambique and Senegal.
We assist asphalt mixing plants, road contractors, highway developers, civil engineering companies and procurement teams with specification matching, bulk quotations and international shipment arrangements.
Trusted supplier and exporter of building construction products in UAE, Saudi, Qatar, Oman & African Countries.
Still confused?
We are happy to help on our expertise with no conditions.